How To Remove and Replace Windshield Wipers and Blades 

feat-replace-wiper-blade

As an Amazon Associate, Modded gets commissions for purchases made through links in this post.

Wiper blades might seem indestructible, but they don’t last forever. Even if you take good care of them, months of wiping snow, rain, dirt and dead bugs off your windshield will eventually render them useless. The end result? Sticky blades that make a smudgy mess and block your line of sight. Some can even make horrible screeching sounds when the rubber begins to peel off the blade. You need to remove your windshield wipers now and again.

Even your windshield wipers themselves — this includes the arm — can bend and break after months or years of use. Luckily, removing and replacing your windshield wipers and blades is simple and affordable. In fact, you could easily buy replacements and save yourself some money just doing the job yourself. 

Replacing the Blades

Wiper blades, or squeegees, should last anywhere from six to 12 months, depending on where you live and how often you drive your car. When they need replacing, order a set of blades online. Most blades deteriorate at the same rate, regardless of how much you pay, so look for a cheap set that’ll fit your wipers. 

Ask an auto-parts store for the proper fit if you’re having trouble choosing the right size. A mechanic will also be able to tell you whether or not the blades need replacing if you’re having any doubts. 

When you find the best fit, follow the steps below to remove your old blades and install the new ones: 

  1. Raise the wipers so they hang above the windshield without touching the glass. 
  2. Use a flathead screwdriver to depress the clip underneath the wiper and remove the blade. If there is no clip, look for a hook-slot or pin-type connector and either press or pull it to release the blades. 
  3. Next, install the new blade. This process will once again depend on which fastener or connector you have. However, most models should simply slide right onto the wiper arm. 
  4. Pull up on the blade to lock it into place. You should hear a small click. Give it a few gentle tugs to ensure it’s secure before laying the wipers back down on your windshield. 
  5. Last but not least, refill your windshield wiper fluid so your brand new blades can go to town on that grimey glass. If your vehicle has a rear wiper, you may have to add more liquid to its reservoir, too. Check both containers every week or so to ensure you don’t run out.  

Removing and Replacing Your Windshield Wipers 

When your wiper blades do need replacing, inspect the windshield wiper arms as well. Are they showing signs of wear and tear? Take your car for a quick test drive. If the wipers sputter, make a squeaking or grinding noise, leave streaks or barely touch the windshield, you may have to shell out a little more cash for entirely new windshield wipers. 

Don’t worry! They’re not that much more expensive than the blades. In fact, you might save money in the long run by simply purchasing them together. 

When you’re ready to complete the installation, follow these steps: 

  1. First, lift the wipers and place a piece of cardboard under them to protect the glass. 
  2. Remove bolt-on wipers by unscrewing the nut that attaches them to the drive arm. If you have clip on wipers, simply release the clip. Spring-loaded wipers require you to press a pin to release them from the arm. 
  3. Pull the wiper arms from their post and set them aside. 
  4. Use a small wire brush to scrub off any rust and debris from threaded posts and apply a drop of oil to the threads. 
  5. Align the new wipers with the attachment point on each post. Slide, tap, press or pull it into place.
  6. If you have an older vehicle, you may have to secure the wiper arm to the base, which you can find under the hood. Use a socket wrench to twist and tighten the nut back onto the drive post before replacing the cover. 

Driving with Confidence and Clean Windshield

You’ve just spent all this time learning how to remove your windshield wipers or perhaps even the wipers themselves. The last thing you want now is to get in the car, turn on your wipers and have them go flying off onto the road. Even if you’re driving at slow speeds, you could put yourself and other drivers in danger in this worst-case scenario. 

That’s why you should test your windshield wipers and blades before hitting the open road. If it’s raining, sit in idle and turn them on to make sure everything works as it should. Otherwise, you can pour some water on your windshield or turn on the sprinkler to give everything a quick test run. Once you get the green light, you can put pedal to the metal and drive with confidence — and a clear view. 


Author